Page 1 of 3
ROLITE COMPANY
596 PROGRESS DRIVE
HARTLAND, WI 53029
INFORMATION: (262) 367-2711
EMERGENCY: CHEM-TEL (800) 255-3924
FAX: (262) 367-2933
E-MAIL: roliteco@execpc.com
MATERIAL SAFETY DATA SHEET
PRODUCT INFORMATION
Trade Name: ROLITE METAL POLISH
Description: Metal Polish
HAZARDOUS INGREDIENTS
MATERIAL OR COMPONENT CAS# OSHA PEL TLV UNITS) APPROX.%
Petroleum Distillates 64742-47-8 500 ppm 100 ppm >20
Ammonium Hydroxide 1336-21-6
NON-HAZARDOUS INGREDIENTS
TRADE SECRET
TSRN 80100300-5000p TSRN 80100300-5001p TSRN 80100300-5002p TSRN 80100300-5003p
TSRN 80100300-5004p
(As established by the Standard Promulgated by the Occupational Safety and Health Administration (OSHA)
PHYSICAL DATA
BOILING POINT, OF NE
SOLUBILITY IN WATER Negligible
SPECIFIC GRAVITY (H2O=1) 1.09
VAPOR PRESSURE (mmHg) NE
VAPOR DENSITY, (AIR=1) NE
EVAPORATION RATE (Butyl Acetate=1) >1
MELTING POINT NA
APPEARANCE Pink Paste
ODOR Slight ammonia
pH 8.5
VOC 22% by weight
HAPS Trace Amount (less that .1%)
FIRE AND EXPLOSION HAZARD DATA
FLASH POINT (method used): Seta-Flash closed cup above 220oF
FLAMMABLE LIMITS: LOWER: NA UPPER: NA
EXTINGUISHING MEDIA: Dry foam
SPECIAL FIRE FIGHTING PROCEDURES: None
UNUSUAL FIRE AND EXPLOSION HAZARDS: None
Rolite Metal Polish
Page 2 of 3
REACTIVITY DATA
STABILITY: STABLE: X UNSTABLE:
INCOMPATIBILITY (MATERIALS TO AVOID): Oxidizing Agents
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide
HAZARDOUS POLYMERIZATION: OCCUR: WILL NOT OCCUR: X
CONDITIONS TO AVOID: NA
HMIS/NFPA LABEL INFORMATION
KEY: HMIS NFPA
0 - MINIMAL HEALTH: 1 1
1 - SLIGHT FLAMMABILITY: 0 0
2 - MODERATE REACTIVITY: 0 0
3 - SERIOUS
4 - SEVERE
HMIS = HAZARDOUS MATERIALS IDENTIFICATION SYSTEM NFPA = NATIONAL FIRE
PROTECTION ASSOC.
REGULATORY INFORMATION
DOT PROPER SHIPPING NAME: Polishing Compound N.O.I.
DOT CLASS: 55
DOT NUMBER: NA
CALIFORNIA PROPOSITION 65: This product does not contain any chemicals currently on the California list of known carcinogens and reproductive toxins.
HEALTH HAZARD DATA
ROUTES OF ENTRY: INHALATION:X SKIN: X INGESTION: X
HEALTH HAZARDS (ACUTE & CHRONIC):
SIGNS AND SYMPTOMS OF EXPOSURE: Slight nausea. Skin irritation and redness.
CARCINOGENICITY: NTP? IARC MONOGRAPHS? OSHA REGULATED?
None known None Known None Known
EMERGENCY AND FIRST AID PROCEDURES: Eyes: Flush with water for a minimum of 15 minutes. See physician immediately. Skin: Wash with plenty of soap and water.
SPILL, LEAK AND DISPOSAL PROCEDURES
ACTION TO TAKE FOR LEAKS OR SPILLS: Scoop up spill in a conventional manner, then clean area with absorbent towels.
DISPOSAL METHOD: Dispose of according to all federal and local regulations.
SPECIAL HANDLING INFORMATION
VENTILATION: Local recommended
RESPIRATORY PROTECTION: None needed unless you will be exposed beyond the PEL and TLV limits. If this is the case, use OSHA regulated respirators.
PROTECTIVE CLOTHING: Coveralls
PROTECTIVE GLOVES: Plastic. Recommended for easier clean-up
EYE PROTECTION: Recommended. Safety
OTHER PROTECTIVE EQUIPMENT: None
WORK/HYGIENIC PRACTICES: Wash hands thoroughly before food intake. Do not inhale or expose to skin over prolonged periods of time.
Rolite Metal Polish
Page 3 of 3
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE
Do not store below 32oF or above 150oF.
This data is furnished gratuitously in keeping with prevailing regulations and is independent of any sales of the product. Rolite Company urges each customer or recipient of this MSDS to
become aware of and understand the hazards associated with the product. The reader should consult references or experts in ventilation, toxicity and fire prevention as necessary to understand
and use the data contained herein. While the information is believed to be correct, Rolite Company accepts no responsibility for any damages resulting from the publication, use or reliance upon
the data contained herein without independent verification. Since the use of this information and the conditions of the use of the product are not within the control of Rolite Company, it is the
user's obligations to determine and observe the conditions of safe use of the product.
Last Revised: June, 203/04